The Best HPE6-A69 Exam Study Material Premium Files and Preparation Tool (Dec-2024)
Get Instant Access to HPE6-A69 Practice Exam Questions
HP HPE6-A69: Aruba Certified Switching Expert Written Exam is a challenging exam that requires a thorough understanding of switching concepts and Aruba products and technologies. However, passing HPE6-A69 exam can open up new career opportunities and provide a competitive advantage in the field of networking.
NEW QUESTION # 32
A customer would like to utilize some ArubaOS-CX 6300F switches to perform OSPF routing.
With the ports set up as routed ports, and default parameters for OSPF. what is me OSPF cost for me connection between SW-3 and SW-4"?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
NEW QUESTION # 33
A customer with an ArubaOS-CX 6300M switch is having a performance issue on the network and has received complaints about users experiencing intermittent connectivity. After performing troubleshooting it is determined that many of the local websites on the LAN that users are unable to reach are resolved to an invalid MAC address What are the minimum steps that should be performed to mitigate this condition? (Select two.)
- A. Enable 'arp inspection' on the end-user physical ports
- B. Implement ARP ACLs to define trusted MAC address to IP bindings
- C. Enable 'arp inspection untrusted' on the end-user physical ports
- D. Enable 'arp inspection' on the end-user VLAN
- E. implement dhcpv4-shooping.
Answer: B,D
NEW QUESTION # 34
Which functionalities of ClearPass can be added in a wired network that implements dynamic segmentation?
(Select two.)
- A. Multi Factor Authentication
- B. Downloadable user Roles
- C. Fingerprinting
- D. Profiling
- E. Dynamic VLANs
Answer: A,E
NEW QUESTION # 35
How Is voice Traffic prioritized correctly on ArubaOS-CX switches?
- A. By implementing TOS-profiles
- B. By defining voice VLANs inside VLAN context
- C. By placing it in the strict priority queue
- D. By attaching the QoS settings directly to device profiles
Answer: A
NEW QUESTION # 36
Match the repotted status to the Aruba 8325 issue (Each option may Be used once more than once, or not at all)
Answer:
Explanation:
NEW QUESTION # 37
You have created an OSPF neighbor configuration with ArubaOS-CX 8320 VSX and a third-party switch The OSPF peering falls. In the event togs you see the following entries.
2020-10-28:03:14 20.371489|hpe-routlng|LOG_WARN|AMM|1/5jOSPFV2|OSPFV2iOSPF 268698624 Packet received with unexpected authentication type
2020-10-28:03:14.20.371503|hpe-routing|LOG_WARN|AMM|1/5|OSPFV2|OSPFV2|Expected authentication type = 0 Which statement is true about the above events?
- A. The third-party switch should be configured with MD5 authentication
- B. The third-party switch should be configured with key chain authentication
- C. The ArubaOS-CX switch does not expect authentication with OSPF.
- D. The ArubaOS-CX switch requires plain-text authentication with OSPF.
Answer: B
NEW QUESTION # 38
A customer with an ArubaOS-CX 6300M switch is having a performance issue on the network and has received complaints about users experiencing intermittent connectivity. After performing troubleshooting it is determined that many of the local websites on the LAN that users are unable to reach are resolved to an invalid MAC address.
What are the minimum steps that should be performed to mitigate this condition? (Select two)
- A. Enable 'arp inspection untrusted on the end-user physical pons
- B. Implement dhcpv4-snooping
- C. Enable 'arp inspections on the end-user VLAN.
- D. Enable 'arp inspection' on the end-user physical ports
- E. Implement arp ACLs to define trusted MAC address to IP bindings
Answer: C,E
NEW QUESTION # 39
When an ArubaOS-CX switch uses the temporary copy of the coring state database, how does NetEdit validate if the configuration is correct?
- A. Syntax validation
- B. Planned validation
- C. Semantic validation
- D. Deploy validation
Answer: B
NEW QUESTION # 40
Refer to the exhibit.
Which statement is true?
- A. Q1 and S1 are applied to all interfaces mat do not have a QoS override applied
- B. To be effective, both Q1 and S1 still need to be applied to Interfaces
- C. Q1 and S1 are applied to all interfaces.
- D. No default queues are changed
Answer: D
NEW QUESTION # 41
Refer to the exhibit.
* For all traffic within VLAN 10. a remark action or DSCP value EF must be set
* For all traffic exiting VLAN 10, a remark action of DSCP value AF41 must be set Which is the correct configuration?
A)
B)
C)
D)
- A. Option D
- B. Option C
- C. Option B
- D. Option A
Answer: D
NEW QUESTION # 42
Match the BGP path selection criteria attributes (Each option may be used once, more than once, or not at all)
Answer:
Explanation:
NEW QUESTION # 43
Refer to the exhibit.
Aruba CX 6300 switch has routes in three different VRFs as per the example above. The user needs to leak routes between VRF Secure and VRF Dev. and also between VRF default and VRF Dev The customer Is not able to establish routing between directly connected networks 10.100.50.0/24 and
10.102.26.0/24 Which statement is true regarding the routing troubleshooting?
- A. Route Distinguisher needs to be set to 1 for default VRF.
- B. Multi-protocol BGP routing needs to be defined for route leaking
- C. Route leaking is supported between non-default VRFs only
- D. Route leaking between default and non-default VRFs is supported with Aruba CX 8400.
Answer: B
NEW QUESTION # 44
(Scenarios may contain multiple errors which may or may not impact the solution) Refer to the Exhibit.
An engineer has attempted to configure two pairs of switches m the referenced configuration it Is required to implement Multi-Chassis Link Aggregation for each pair of switches The ports of the Aruba 8325 switches used for Agg01 and Agg02 are populated as follows
The configuration includes:
There is an error message stating "mismatched group speed" What should you add to the configuration to correct the error?
- A. "speed 40-full" under interfaces 1/1/49 and 1/1/50
- B. "system Interface-group 1 speed I0g"
- C. "speed 10-full" under interfaces 1/1/12 and 1/1/13
- D. "allow-unsupported-transceiver
Answer: C
NEW QUESTION # 45
The customer is already using Aruba Gateway and third-party L2 switches New ArubaOS CX 6300 switches have been deployed for R&D. which have a requirement for user profiling and tunneled traffic between ArubaOS CX 6300 and Aruba Gateway What is required for this configuration to apply QoS user-based rules for the R&D client traffic?
- A. Create a QoS policy for the UBT-client-VLAN traffic on the third-party switch.
- B. Manually prioritize IP protocol 47 traffic on the third-party switches to prioritize the tunneled traffic
- C. Apply a port-access policy with QoS defined in the user role on the ArubaOS CX6300 switch
- D. Apply a QoS rule to the ArubaCX 6300 client port, lo classify traffic before it is tunneled.
Answer: D
NEW QUESTION # 46
The rate-limiting QoS feature can be implemented on all ArubaOS-CX platforms However, some features are platform dependent. Which statements are true'' (Select two.)
- A. ICMP-Rate limiting is supported on all ArubaOS-CX platforms.
- B. Unknown unicast rate limiting is supported on all ArubaOS-CX platforms
- C. Broadcast-rate limiting is supported on all ArubaOS-CX platforms
- D. Multicast and broadcast rate limits cannot be applied at the same time on the same Interface
Answer: A,D
NEW QUESTION # 47
Which statement is true regarding remote mirroring?
- A. The ArubaOS-CX switch supports a maximum of two mirroring sessions
- B. Per session multiple destination addresses can be configured
- C. The same source/destination address can be used in multiple sessions.
- D. When mirroring destination is tunnel, a DSCP value can be set on the tunnel
Answer: B
NEW QUESTION # 48
(Scenarios may contain multiple errors which may or may not Impact the solution > Refer to the exhibit.
An engineer has attempted to configure two pairs of switches in the referenced configuration it is required to implement VSX keep-alive at the aggregation layer.
The ports of the ArubaOS-CS 8325 switches used for Agg01 and Agg02 are populated as follows:
The configuration of switch AGG01 includes:
VSX keep-alive is not working. Which modification should you make lo resolve the error condition?
- A. Modify the Interface lag 2 command, removing "multi-chassis"
- B. Edit interface 1/1/48, adding the command "vpn-instance KA"
- C. Modify the Keepalive peer 192.168.20.2 source 192 168.20.1 command, adding "vrf KA"
- D. Edit the vsx-sync command, adding "keep-alive"
Answer: A
NEW QUESTION # 49
A customer wants to implement a new Aruba 6300M 48-port iGbE Class 4 PoE and d-port SFP56 Switch solution. The customer wants to automatically provision devices, connected to the switch with correct settings.
VoIP phones need to be placed in VLAN 10, send out traffic with a VLAN tag. The phone is LLDP-MED capable How can you accomplish this with the least amount of administrative effort?
A)
B)
C)
D)
- A. Option D
- B. Option C
- C. Option B
- D. Option A
Answer: D
NEW QUESTION # 50
A customer would like to utilize some ArubaOS-CX 6300F switches to perform OSPF routing.
With the ports set up as routed ports, and default parameters for OSPF, which action is the simplest way to allow the fastest communication...
- A. No action is required
- B. Set the OSPF reference bandwidth to 10 or higher
- C. Set the OSPF cost parameters on every interface on every switch according to the Bandwidth or each link
- D. Utilize Equal-cost multi-path routing to aggregate more bandwidth on the WAN.
Answer: A
NEW QUESTION # 51
......
HP HPE6-A69 exam is a valuable certification test for networking professionals who want to validate their expertise in Aruba switching technologies. Passing the exam and earning the ACSE certification can help you advance your career and demonstrate your knowledge to potential employers. However, to succeed, you must prepare thoroughly and have a solid understanding of the exam topics.
Validate your Skills with Updated HPE6-A69 Exam Questions & Answers and Test Engine: https://www.testsimulate.com/HPE6-A69-study-materials.html