Get HPE0-V14 Actual Free Exam Q&As to Prepare for Your HP Certification
HP Actual Free Exam Questions And Answers
NEW QUESTION 103
A system administrator is performing the BIOS/Platform configuration of a DL380 Gen10 servers You notice the amber health LED.
The health status of which solution components can be verified with embedded UEFI Diagnostics? {Select two.)
- A. Processor
- B. Power Supplies
- C. FC HBA
- D. Primera node
- E. iLONAND
Answer: B,D
NEW QUESTION 104
You are configuring an MSA 2052 for one of your customers in OCA.
Click on either one of the two places on the Bill of Materials screen that will enable you to verify the configuration and get details on any errors
Answer:
Explanation:
NEW QUESTION 105
Match the Networking Product Family to the appropriate use case:
Answer:
Explanation:
NEW QUESTION 106
Read the question, and then refer to the exhibit.
display interface Ten-GigabitEthernet 1/0/1 Ten-GigabitEthernet1/0/1 Current state: Administratively DOWN Line protocol state: DOWN IP packet frame type: Ethernet II, hardware address: d894-03fb-793d Description: Ten- GigabitEthernet1/0/1 Interface Bandwidth: 10000000 kbps Loopback is not set Media type is stack wire, port hardware type is STACK_SFP_PLUS Unknown-speed mode, unknown-duplex mode Link speed type is autonegotiation, link duplex type is autonegotiation Flow-control is not enabled Maximum frame length: 10000 Allow jumbo frames to pass Broadcast max-ratio: 100% Multicast max-ratio: 100% Unicast max-ratio: 100% PVID: 1 MDI type: Automdix Port link-type: Trunk VLAN Passing:
10, 20 VLAN permitted: 10, 20 Trunk port encapsulation: IEEE 802.1q Port priority: 0 Last link flapping: 0 hours 0 minutes 18 seconds Last clearing of counters: Never Peak input rate: 78 bytes/sec, at 2011-03-31 04:55:57 Peak output rate: 15 bytes/sec, at 2011-03-30 23:00:57 Last 300 second input: 0 packets/sec
67 bytes/sec - % Last 300 second output: 0 packets/sec 14 bytes/sec - % Input (total): 62670 packets, 8565340 bytes 0 unicasts, 0 broadcasts, 62670 multicasts,
0 pauses Input (normal): 62670 packets, - bytes 0 unicasts, 0 broadcasts, 62670 multicasts, 0 pauses Input: 0 input errors, 0 runts, 0 giants, 0 throttles 0 CRC,
0 frame, - overruns, 0 aborts - ignored, - parity errors Output (total): 3707 packets, 1294835 bytes 0 unicasts, 0 broadcasts, 3707 multicasts, 0 pauses Output (normal): 3707 packets, - bytes 0 unicasts, 0 broadcasts, 3707 multicasts, 0 pauses Output: 0 output errors, - underruns, - buffer failures 0 aborts, 0 deferred, 0 collisions, 0 late collisions 0 lost carrier, - no carrier A customer added a new switch to their network. They connected it using interface Ten-GigabitEthernet 1/0/1.
They are using VLAN 10 and 20 for the devices in their network.
The new switch was fully operational. Then, the customer experienced a power failure later that day and could not reach any device on the new switch after the power returned.
From the output in the exhibit, would could be the issue?
- A. The interface is administratively down.
- B. The interface is configured for a PVID of VLAN 1.
- C. The interface loopback is not set.
- D. The interface link-speed and duplex are unknown.
Answer: B
Explanation:
Explanation/Reference: https://assets.ext.hpe.com/is/content/hpedam/a00004216enw
NEW QUESTION 107
A solution integrator is installing new data center components including an HPE G2 Advanced Rack with two Standard Series G2 PDUs A customer observing the installation process questions whether there will be sufficient power for additional equipment that may be added in the future.
How should the solution integrator respond'?
- A. HPE G2 Advanced racks allow additional PDUs to be added if additional equipment requires more outlets or more available power
- B. Two HPE Standard G2 PDUs will support 42U of racked equipment, so any equipment added in the future will be accommodated by the current PDU configuration
- C. HPE Standard Series G2 PDUs allow additional inlet power cords to support additional equipment in the future.
- D. HPE PDUs support elevated temperatures up to 75°C (1673F), in case the additional equipment power draw results in increased heat generation.
Answer: C
NEW QUESTION 108
Match each HPE solution to its corresponding technology usage.
Answer:
Explanation:
NEW QUESTION 109
A customer has a single ProLiant DL580 Gen10 running ESXI 7.0. They want to remotely power on the server.
Which locally available management tool should they use to complete this task?
- A. ILO Amplifier Pack
- B. HPE Composer
- C. HPE Oneview standard
- D. ILO Advanced
Answer: D
NEW QUESTION 110
HPE Support asks you to generate an SSD wear gauge report for local storage on an HPE DL360 Gen10 server running VMware.
Which procedure will ensure that the server will boot directly into a maintenance state so you can generate the requested report?
- A. Click Boot to System Setup Utilities in iLO web-based user interface
- B. Changing the one-time boot option to Smart Storage Administrator in iLO web-based user interface
- C. Changing the one-time boot option to Intelligent Provisioning in iLO web-based user interface
- D. Use Always On functionality of Intelligent Provisioning
- E. Changing the one-time boot option to Intelligent Provisioning in HPE OneView
Answer: C
Explanation:
Reference:
https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-a00051235en_us
NEW QUESTION 111
Match each HPE solution to its corresponding technology usage.
Answer:
Explanation:
Explanation
NEW QUESTION 112
A customer is subject to regulatory requirements and their data is highly sensitive.
Which HPE Smart Array feature addresses their need for an additional level of security for data stored inside their server?
- A. Rapid Parity Initialization
- B. Smart Battery backed-up write-cache
- C. Secure Encryption
- D. SmartCache
Answer: D
NEW QUESTION 113
Match the HPE Tool with its use case. Select all that apply.
Answer:
Explanation:
NEW QUESTION 114
Match the storage technology to the storage type.
Answer:
Explanation:
Explanation
BLOCK = iSCSi
File = CIFS
BLOCK = SAN
File = NFS
NEW QUESTION 115
A customer needs to update firmware and perform diagnostic tests on various components of a HPE ProLiant server.
Which utility should they use?
- A. Insight Online
- B. Intelligent Provisioning
- C. UEFI
- D. Intelligent Management Center
Answer: B
NEW QUESTION 116
A customer has a VMware environment with HPE ProLiant servers and Nimble storage. They have been using a Windows VM to provide file services for their employees.
The customer is experiencing performance issues with the solution due to memory constraints on the virtual environment.
What could be added to the existing environment that will provide dedicated file services with better performance that would still utilize the existing storage and backup solutions?
- A. HPE StoreEasy 1460 Storage
- B. HPE Storage Performance File Controller
- C. HPE StoreEver 30750
- D. HPE StoreEasy 1650 Expanded Storage
Answer: A
Explanation:
Explanation/Reference:
NEW QUESTION 117
A customer needs to locate an exact time when a link down event occurred at the FC port of Nimble storage
Which on-premises tool can the customer use?
- A. HPE Nimble Storage web-based user interface
- B. HPE InfoSight
- C. Embedded UEFI Diagnostics
- D. HPE StoreServ Management Console
Answer: B
NEW QUESTION 118
A customer needs a solution for a rack of servers. They need connectivity for 14 HPE DL380 servers, which each have two 10-GBASE-T Ethernet ports, and 10 HPE DL360 servers, which have two 10GBASE-X SFP+ Ethernet ports.
They need switch redundancy for each server and want to connect all servers to the same switch stack. The client also needs a 400 Gb backbone connection to the data center core switch from the solution you are creating.
Which architecture meets the customer requirements?
- A. One VSX stack of two Aruba 8325 48-port 1/10GBASE-X SFP+ switches with the following: 14 10GBASE-T transceivers in each switch
10 SFP+ to SFP+ DACs in each switch - B. One VSX stack of two Aruba 8320 48-port 1/10GBASE-X SFP+ switches with the following: 14 10GBASE-T transceivers in each switch
10 SFP+ to SFP+ DACs in each switch Two QSFP+ to Quad SFP+ adapters - C. One IRF stack of wo HPE 5945 2-Slot switches each with the following: One 24-Port SFP28 + 2-Port QSFP28 module
One 24-Port 1/10GBASE-T + 2-Port QSFP+ module 10 SFP+ to SFP+ DACs in each switch - D. One IRF stack of two HPE 5945 48-port 1/10GBASE-X SFP+ switches with the following: 14 10GBASE-T transceivers in each switch
10 SFP+ to SFP+ DACs in each switch
Answer: D
NEW QUESTION 119
A customer with limited IT administration resources needs a complete HPE server, storage, and networking solution. The solution must be able to be deployed in an hour or less through a simple, wizard-based setup.
They want to manage the HPE solution through a simple, integrated plug-in to vCenter, since their IT staff members are already familiar with vCenter.
Which HPE solution best meets the customer requirements?
- A. HPE ConvergedSystem 750
- B. HPE Proliant for Microsoft Azure Stack
- C. HPE OneView for VMware vCenter
- D. HPE Nimble Storage dHCI
Answer: D
NEW QUESTION 120
Refer to the exhibit.
A customer has been using VEEAM and the HPE StoreOnce 3620 shown in the exhibit to backup their environment. The customer's legal team has asked to double their retention times for all backup sets, and they are starting to run out of space on the StoreOnce.
Which options could you recommend that the customer add to their existing configuration to accommodate the new requirement? (Select two. Each option represents a separate solution.)
- A. HPE StoreOnce Gen4 10/25Gb SFP Network card
- B. HPE StoreOnce Gen4 16Gb Fibre Channel Network Card
- C. HPE D3710 Storage Enclosure
- D. HPE StoreOnce Cloud Bank Storage
- E. HPE StoreOnce 3620 24TB Capacity Upgrade Kit
Answer: D,E
Explanation:
Reference: https://www.hpe.com/uk/en/product-catalog/storage/disk-based-backup-systems/ pip.specifications.hpe-storeonce-systems.1011014655.html
NEW QUESTION 121
Which HPE solution brings together CPU, Memory, and Disk with an unpredictable workload into a single management infrastructure?
- A. Primera
- B. Nimble
- C. dHCI
- D. SimpliVity
Answer: D
NEW QUESTION 122
Match the characteristic to the correct HPE ProLiant family.
Answer:
Explanation:
NEW QUESTION 123
A client complains about systems reliability issues caused by their staff's inability to identify the root cause of failures. The client's lead administrator wants to automatically send data from HPE OneView to additional listeners in the network.
What should you configure in HPE OneView to enable the external monitoring of the managed devices?
- A. Configure a scope to include the listener.
- B. Configure SNMP Trap Forwarding.
- C. Configure scheduled reports to export the data to the listener.
- D. Configure the listener as a managed device.
Answer: B
Explanation:
Reference: https://h20195.www2.hpe.com/v2/getpdf.aspx/4AA5-3811ENW.pdf?
NEW QUESTION 124
Match the Networking Product Family to the appropriate use case:
Answer:
Explanation:
NEW QUESTION 125
A customer plans to purchase five HPE DL380 Gb 2-port 530SFP Ethernet Adapters. The customer's network administrator has Installed a top of rack 10 GbE switch capable of supporting copper and optical connections. The customer is already over budget and needs to keep costs down.
Which option should you recommend Tor connecting to the switch?
- A. 3m Cat 6A Copper Cables
- B. 3m OM3 Fiber Optic Cables
- C. 3m OM2 Fiber optic cables
- D. 3m Direct Attached Copper Cables
Answer: D
NEW QUESTION 126
Which HPE service level offers customers special parts handling and access to onsite service 24x7, including HPE holidays?
- A. Proactive Care 24x7 with CTR
- B. Foundation Care 24x7 with DMR
- C. Proactive Care 24x7
- D. Foundation Care 24x7
Answer: D
NEW QUESTION 127
Exhibit:
Which HPE ProLiant Server meets the customer's requirements?
- A. Option D
- B. Option B
- C. Option A
- D. Option C
Answer: B
NEW QUESTION 128
......
HPE0-V14 Questions Truly Valid For Your HP Exam: https://www.testsimulate.com/HPE0-V14-study-materials.html