2025 Realistic D-PSC-MN-23 Dumps Questions To Gain Brilliant Result
Start your D-PSC-MN-23 Exam Questions Preparation with Updated 142 Questions
NEW QUESTION # 20
Before a PowerScale node can be put into operation after maintenance, what is an essential task?
- A. Updating the node's firmware
- B. Restoring user data
- C. Running a system health check
- D. Performing a full system backup
Answer: C
NEW QUESTION # 21
A platform engineer is connecting a new Dell PowerScale F200 node to the front-end switch.
How should the network cables be connected?
- A. From PCIe slot 1 to the front-end Ethernet switch
- B. From the rNDC slot to the front-end Ethernet switch
- C. From PCIe slot 3 to the front-end Ethernet switch
- D. From the rNDC slot to the front-end InfiniBand switch
Answer: B
NEW QUESTION # 22
In the context of PowerScale hardware installation, why is it essential to verify the firmware version of each node?
- A. To comply with data security regulations
- B. To ensure compatibility with the cluster's existing nodes
- C. To confirm that all nodes will operate at the same performance level
- D. To facilitate integration with third-party applications
Answer: B
NEW QUESTION # 23
A Dell PowerScale Gen 6 chassis is scheduled to be installed in a rack.
What is a valid recommendation?
- A. When using a mechanical lift, the drive sleds and compute modules need to be removed first.
- B. When the drive sleds and compute modules are removed, one person is allowed to lift the chassis.
- C. When using a mechanical lift, two people are required to install the chassis into the rack.
- D. When the drive sleds and compute modules are removed, two people need to lift the chassis.
Answer: D
NEW QUESTION # 24
When should the customer engineer document and register a Dell PowerScale system in the install base record?
- A. After OneFS has been initialized and configured
- B. After racking the system
- C. Before OneFS has been initialized, configured, and updated
- D. Before racking the system
Answer: B
NEW QUESTION # 25
In the context of PowerScale, what are critical steps in the rack installation process?
- A. Aligning the rack for optimal airflow
- B. Ensuring compatibility with PowerScale node dimensions
- C. Determining the rack's load capacity
- D. Securing the rack to the floor
Answer: D
NEW QUESTION # 26
During a PowerScale cluster expansion, what factors must be considered to maintain balance?
- A. Data distribution and redundancy settings
- B. Storage and compute node ratios
- C. Power and cooling requirements
- D. Network throughput and latency
Answer: B,D
NEW QUESTION # 27
What is the recommended way to install a Dell PowerScale Gen 6 compute module in a chassis?
- A. Loosen the thumbscrew on the release lever then slide the compute module into the chassis.
- B. Close the module lever and slide the module into the chassis until it clicks.
- C. Slide the release lever to the right and guide the node into the chassis.
- D. Support the node with both hands and slide it into the node bay.
Answer: D
NEW QUESTION # 28
Refer to the exhibit.
A platform engineer has connected power cables to a Dell PowerScale Gen 6 node.
What do the status lights indicate?
- A. On and healthy
- B. Not functioning
- C. Warning event
- D. Cold and redundant
Answer: C
NEW QUESTION # 29
What procedure is recommended for applying patches to a PowerScale cluster?
- A. Applying patches to a single node first as a test
- B. Manually patching each node to monitor the process closely
- C. Using automated tools to distribute and apply patches cluster-wide
- D. Broadcasting the patch simultaneously to all nodes
Answer: C
NEW QUESTION # 30
A Dell PowerScale platform engineer is on site to perform a node replacement. The serial number on the tag does not match the serial number provided by the customer. The platform engineer suspects the tag is incorrect.
Which command can they run to obtain the serial number of the node?
- A. isi devices | grep SerNo
- B. isi_hw_status -i
- C. isi status -q
- D. isi_nodes %<id> %<name>
Answer: B
NEW QUESTION # 31
A platform engineer plans to set up a rack system for a Dell PowerScale cluster installation.
What is a requirement for the initial setup?
- A. The rack cabinet must have at least dual power supplies with power distribution.
- B. Grounding lugs must be used for internal grounding within the chassis.
- C. Power cords must be connected to four power distribution units within the rack cabinet.
- D. The rack system must have twelve independent 200-240 V power sources.
Answer: A
NEW QUESTION # 32
According to Dell PowerScale best practices, which component may be replaced by the customer?
- A. Fan
- B. Battery
- C. Power supply
- D. M.2 vault card
Answer: C
NEW QUESTION # 33
In PowerScale hardware maintenance, why is it essential to track the installation and maintenance of FRUs?
- A. To provide a history for troubleshooting and diagnostics
- B. To facilitate future software upgrades
- C. To ensure optimal data placement within the cluster
- D. To maintain a detailed inventory for audit purposes
Answer: D
NEW QUESTION # 34
What is crucial when reformatting a PowerScale node during its addition to a cluster?
- A. Setting up the node's network interfaces
- B. Verifying that the new format is compatible with existing nodes
- C. Configuring the node to boot from an external USB drive
- D. Ensuring the node's data is backed up
Answer: B
NEW QUESTION # 35
......
Easy Success EMC D-PSC-MN-23 Exam in First Try: https://www.testsimulate.com/D-PSC-MN-23-study-materials.html