Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-363) Free Practice Test

Question 1

Which LSA type does an OSPF ABR use to advertise external routes generated by an NSSAASBR into the backbone?

A. Type 7

B. Type 1

C. Type 3

D. Type 5

Correct Answer: A

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 2

What is the correct order of BGP attributes for active route selection?

A. next hop -> origin -> local preference -> AS path -> MED

B. next hop -> local preference -> AS path -> origin -> MED

C. next hop -> local preference -> AS path -> MED -> origin

D. next hop -> AS path -> local preference -> origin -> MED

Correct Answer: B

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 3

When would you use the qualified-next-hop statement with a static route?

A. You can use it to resolve the next hop if the next hop is not directly connected.

B. You can use it to install the static route into different routing tables.

C. You can use it to specify multiple next hops with different preferences.

D. You can use it to send unwanted traffic to a null route.

Correct Answer: C

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 4

Which BGP message type is used to re-advertise routes that have already been sent to a peer and acknowledged using TCP?

A. refresh

B. keepalive

C. update

D. notification

Correct Answer: C

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 5

Exhibit

You have configured graceful RE switchover (GRES), however you cannot complete the show system switchover command.
Referring to the exhibit, what is the problem?

A. The command is only available If graceful restart is enabled.

B. The command is only available on the backup Routing Engine.

C. The command is only available If a backup router is configured.

D. The command is only available if non-stop routing is enabled.

Correct Answer: D

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 6

Exhibit

You are asked to configure the OSPF environment to prevent the DRother routers from participating in DR/BDR election.
Referring to the exhibit, which command will accomplish this task?

A. set protocols ospf area 0.0.0.0 interface ge-0/0/1 priority

B. set protocols ospf area 0.0.0.0 interface ge-0/0/l priority 255

C. set protocols ospf area 0.0.0.0 interface ge-0/0/1 interface-type p2p

D. set protocols ospf area 0.0.0.0 interface ge-0/0/1 interface-type nbma

Correct Answer: A

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 7

Exhibit

Referring to the exhibit, what is the minimum number of LSPs required to support alt four networks?

A. 4

B. 8

C. 1

D. 2

Correct Answer: C

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 8

Exhibit

Referring to the exhibit, which statement is true about VRRP?

A. VRRP communication between the two devices is not functioning correctly.

B. The routers should use different virtual IP addresses for VRRP to function correctly.

C. Both routers are in the same state because they have the same VRRP priority.

D. VRRP Is functioning normally in active/active mode.

Correct Answer: D

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 9

Exhibit

Referring to the exhibit, how do you verify the status of the tunnel from R1?

A. Issue the ping 172.20.iii.io source 203.0.113.2 command.

B. Issue the ping 172.20.111.10 source 172.20.110.1 command.

C. Issue the ping 172.20.111.10 source 198.51.100.1 command.

D. Issue the ping 172.20. Ill. 10 command.

Correct Answer: C

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Welcome to TestSimulate

Juniper Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-363) Free Practice Test