NetApp Certified Storage Installation Engineer - ONTAP 9.1 (NS0-181) Free Practice Test

Question 1

Select the Exhibit tab.

You finished the installation of a new FAS8200 system. The customer wants to use FC and 10G Ethernet but only has the onboard UTA2 ports available.
Referring to the exhibit, which two sets of ports would the customer use? (Choose two.)

A. e0e, 0f and e0g, 0h

B. 0e, e0f and 0g, e0h

C. 0e, 0f and e0g, e0h

D. e0e, e0f and 0g, 0h

Correct Answer: A,D

Question 2

You are creating a new aggregate with one RAID -TEC RAID group.
How many parity drives are used in this scenario?

A. 4

B. 3

C. 1

D. 2

Correct Answer: B

Question 3

What is the minimum number of iSCSI LIFs per node in ONTAP 9.1?

A. 4

B. 3

C. 1

D. 2

Correct Answer: D

Question 4

After the installation of the NetApp CN1610 cluster switches, you want to verify that the cabling is correct.
Which protocol will allow you to verify the cabling remotely?

A. Point to Point protocol (PPP)

B. Hyper Text Transfer Protocol (HTTP)

C. Transmission Control Protocol (TCP)

D. Cisco Discovery Protocol (CDP)

Correct Answer: C

Question 5

Recently, your 2-node FAS8020 cluster was upgraded from ONTAP 8.3 to ONTAP 9.1. You have just added two FAS8060 nodes to the cluster. You have executed Config Advisor to verify your work. Config Advisor tells you that the cluster ports on the original two FAS8020 nodes have Flow Control set to FULL.
In this scenario, to what should the Flow Control setting on the FAS8020 ports be set?

A. Flow Control should be set to ALL.

B. Flow Control should be set to SEND.

C. Flow Control should be set to RECEIVE.

D. Flow Control should be set to NONE.

Correct Answer: A

Question 6

What is the main function of ACP?

A. It allows cabling the shelf to two additional controllers.

B. It enables the automatic shelf ID assignment.

C. It allows the controller to nondisruptively reset the SAS expanders.

D. It allows the controller to use Ethernet instead of SAS to fetch the storage data.

Correct Answer: D

Question 7

You have just installed a new FAS2620 on a cluster site. You are using the USB cable for the intial configuration.
In this scenario, what is the default speed for the serial connection?

A. 9600 bps

B. 15200 bps

C. 115200 bps

D. 576000 bps

Correct Answer: C

Question 8

Your customer has filled out the customer installation worksheet. However, the customer's network environment is not set up and ready for the new ONTAP 9.1 system. The customer requests that you install the system and states that they will finish the configuration when they have acquired the appropriate network connections.
Which two statements are correct about this scenario? (Choose two.)

A. You should cable a cluster so that the clusters interconnect traffic is on a separate network from all other traffic.

B. You cannot install an ONTAP system without having the customer network configuration.

C. You should cable all of the controllers and disk shelves, power on the system, and then leave the system as-is for the customer to configure.

D. A cluster can be created without data network connections, but it must include a cluster interconnect connection.

Correct Answer: A,D

Question 9

You are performing a nondisruptive image upgrade of a CN1610 switch. You verify that there are no path failures on the switch.
What is the next step in this process?

A. Backup the current running image using the copy active backup command.

B. Run the write memory command.

C. Run the reload command.

D. Reboot the switch.

Correct Answer: B

Welcome to TestSimulate

Network Appliance NetApp Certified Storage Installation Engineer - ONTAP 9.1 (NS0-181) Free Practice Test