Managing Industrial Networks for Manufacturing with Cisco Technologies (200-601) Free Practice Test

Question 1

Which option allows an EtherNet/IP I/O device to be safely installed where it is subject to water immersion?

A. The device is rated IP20 and immersed to 10 m.

B. The device is rated IP67 and immersed to 10 m.

C. The device is rated IP20 and the power wiring is installed securely to the terminal block.

D. The device is rated IP67 and a power cordset is used.

Correct Answer: D

Question 2

Which two are possible solutions to control which devices can communicate between industrial zones? (Choose two)

A. Attach each zone to a firewall to control intra-zone traffic

B. Deploy an IDS system between the zones to control intra-zone traffic

C. Deploy QoS traffic shaping to limit the volume of traffic between industrial zones

D. Use per zone private IP addressing and deploy NAT to control traffic between zones

E. Put access control lists on switches connecting industrial zones to control traffic

Correct Answer: A,E

Question 3

What are the two most relevant factors in determining the class of administration that is required to maintain the telecommunications infrastructure? (Choose two.)

A. the size of the infrastructure

B. the complexity of the infrastructure

C. the industry that the infrastructure supports

D. the age of the infrastructure

E. the physical environment of the infrastructure

Correct Answer: A,B

Question 4

You have been tasked to design an Ethernet network capable of Motion control with cycle times not to exceed 1ms. In order to create a more deterministic network, what characteristic/s should you primarily focus on?

A. Gigabit port speed

B. This cycle time is not possible on an Ethernet network

C. Lattency and Jitter

D. Redundancy and high availability

E. Explicit and Implicit messaging

Correct Answer: C

Question 5

EtherNet/IP is an Ethernet implementation of which protocol?

A. DeviceNet

B. ControlNet

C. CIP

D. Industrial Protocol

Correct Answer: C

Question 6

What are two benefits of a star network topology? (Choose two.)

A. The performance of the entire network is directly dependent on the performance of the hub.

B. The performance of one of the numerous nodes cannot reflect on the performance of other nodes.

C. Any problem which leaves the network inoperable can be traced to the central hub.

D. Disruption of the entire network is not required when adding new machines.

E. This network type requires less cable as compared to linear bus topology.

Correct Answer: C,D

Question 7

Refer to the exhibit. Which lines represent an I/O connection running at a 20ms RPI?

A. 2922, 2929, 2935

B. 2919, 2923, 2926

C. 2920, 2926, 2929

D. 2914, 2915, 2916

Correct Answer: B

Question 8

Your controller has a high performance EtherNet/IP interface with port speed of >30,000 packets per second and 80% spare capacity. A new PowerFlex 753 drive will be added to the system with an RPI of 2ms and has been connected to a switch; you have been asked to set up the switch port. You open the EDS file and see that the drive will support 16 CIP connections and has transmit and receive capacity of 1,000 control packets per second.
What do you set as the storm control pps threshold limit for the port?

A. 2,500

B. 1,000

C. 16

D. 25,000

Correct Answer: A

Question 9

Exhibit:

Refer to the exhibit. Host 3 on Network A is sending data to Host 8 on Network B.
Which address is the default gateway of Host 3?

A. the address of the switch interface that is connected to router interface Fa0/0

B. the address of the router interface Fa0/1

C. the address of the switch interface that is connected to router interface Fa0/1

D. the address of the host that is connected to Network A

E. the address of the host that is connected to Network B

F. the address of the router interface Fa0/0

Correct Answer: F

Welcome to TestSimulate

Cisco Managing Industrial Networks for Manufacturing with Cisco Technologies (200-601) Free Practice Test