Juniper networks Certified internet associate.m(jncia-m) (JN0-201) Free Practice Test

Question 1

Which boot device contains the primary copy of the JUNOS software?

A. internal flash drive

B. hard drive

C. floppy drive

D. PCMCIA flash

Correct Answer: A

Question 2

What are two advantages of a signaled LSP over a static LSP? (Choose two.)

A. consumes fewer router resources

B. shows up in the route table as a static route

C. supports failover to secondary LSPs

D. performs keep-alive checking

Correct Answer: C,D

Question 3

Which command ensures that a configuration file on a backup Routing Engine is identical to the file on the primary Routing Engine?

A. commit and-quit

B. commit check

C. commit synchronize

D. commit confirmed

Correct Answer: C

Question 4

During OSPF adjacency formation, in what state is a router when it is negotiating to be in charge of the database synchronization process?

A. 2Way

B. Exchange

C. Init

D. ExStart

Correct Answer: D

Question 5

Assume that a comparable configuration is applied to your peer in AS 11 and that bi- directional TCP reachability has been achieved. Which EBGP configuration will allow the BGP session to become established?

A. routing-options { autonomous-system 64; } protocols { bgp { group external-peer11 { type external; neighbor 10.0.3.6 { peer-as 11; } } }

B. routing-options { autonomous-system 64; } protocols { bgp { autonomous-system 64; } protocols { bgp { group external-peer101 { } protocols { bgp { group external-peer101 { peer-as 101; protocols { bgp { group external-peer101 { peer-as 101; neighbor 10.0.3.6; protocols { bgp { group external-peer101 { peer-as 101; neighbor 10.0.3.6; } bgp { group external-peer101 { peer-as 101; neighbor 10.0.3.6; } } group external-peer101 { peer-as
101; neighbor 10.0.3.6; } } peer-as 101; neighbor 10.0.3.6; } } neighbor 10.0.3.6; } } } }
}

C. routing-options { autonomous-system 64; }

D. routing-options { }

E. routing-options { autonomous-system 64; } protocols {

F. routing-options { autonomous-system 64; }

G. routing-options { autonomous-system 11; } protocols { bgp { group external-peer1 { type external; peer-as 11;{ neighbor 10.0.3.6; } }

H. routing-options { autonomous-system 11; } protocols { bgp { group external-peer11 { type external; peer-as 64;{ neighbor 10.0.3.6; } group external-peer11 { type external; peer- as 64;{ neighbor 10.0.3.6; } } type external; peer-as 64;{ neighbor 10.0.3.6; } } peer-as 64;{ neighbor 10.0.3.6; } } neighbor 10.0.3.6; } }

Correct Answer: A

Question 6

Which protocol family is required prior to assigning an IP address to an interface?

A. family inet4

B. family ip6

C. family inet

D. family ip

Correct Answer: C

Question 7

A network administrator would like to verify the active alarms on interface so-0/0/0.0. Which command displays this information?

A. show interfaces terse

B. show alarms

C. show alarms extensive

D. show interfaces extensive

Correct Answer: D

Question 8

When a router receives a label of zero it will _____.

A. perform a label pop

B. perform a label push

C. perform a label swap

D. send an error message toward the ingress router

Correct Answer: A

Welcome to TestSimulate

Juniper networks Certified internet associate.m(jncia-m) (JN0-201) Free Practice Test