Cisco Implementing Cisco Enterprise Advanced Routing and Services (300-410) Free Practice Test
Question 1
Refer to the exhibit. An engineer is troubleshooting an issue using the debug ip packet command
and notices that no time stamps are shown on R4 to establish the event time. Which configuration
resolves this issue by showing time stamps regardless of the time zone in R4 logs?
and notices that no time stamps are shown on R4 to establish the event time. Which configuration
resolves this issue by showing time stamps regardless of the time zone in R4 logs?
Correct Answer: B
Question 2
Refer to the exhibit. An engineer must configure the hub router to add new offices in the same
infrastructure without performing any further configurations at the hub router.
Which tunnel mode configuration on the hub router meets this requirement?
infrastructure without performing any further configurations at the hub router.
Which tunnel mode configuration on the hub router meets this requirement?
Correct Answer: C
Question 3
Refer to the exhibit. A network administrator sets up an OSPF routing protocol for a DMVPN
network on the hub router.
Which configuration required to establish a DMVPN tunnel with multiple spokes?
network on the hub router.
Which configuration required to establish a DMVPN tunnel with multiple spokes?
Correct Answer: B
Question 4
Which 0S1 model is used to insert an MPLS label?
Correct Answer: B
Question 5
Refer to the exhibit. A network administrator is troubleshooting OSPF adjacency issue by going
through the console logs in the router, but due to an overwhelming log messages stream, it is
impossible to capture the problem.
Which two commands reduce console log messages to relevant OSPF neighbor problem details
so that the issue can be resolved? (Choose two.)
through the console logs in the router, but due to an overwhelming log messages stream, it is
impossible to capture the problem.
Which two commands reduce console log messages to relevant OSPF neighbor problem details
so that the issue can be resolved? (Choose two.)
Correct Answer: A,B
Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).
Question 6
Refer to the exhibit. A network engineer notices that R1 and R2 cannot establish an eBGP
peering.
The following messages appear in the log:
Which configuration must the engineer apply to R1 to restore the eBGP peering?
peering.
The following messages appear in the log:
Which configuration must the engineer apply to R1 to restore the eBGP peering?
Correct Answer: B
Question 7
What is the purpose of the DHCPv6 Guard?
Correct Answer: B
Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).
Question 8
What happens when two EIGRP peers have mismatched K values?
Correct Answer: C
Question 9
Which of the following is true regarding IPsec Pre-fragmentation (Look-Ahead Fragmentation)?
(Choose two.)
(Choose two.)
Correct Answer: A,C
Question 10
Refer to the exhibit. Routers R1 and R2 have established a network adjacency using EIGRP, and
both routers are advertising subnets to its neighbor. After issuing the show ip EIGRP topology all-
links command in R1, some prefixes are not showing R2 as a successor. Which action resolves
the issue?
both routers are advertising subnets to its neighbor. After issuing the show ip EIGRP topology all-
links command in R1, some prefixes are not showing R2 as a successor. Which action resolves
the issue?
Correct Answer: C
Question 11
LAB SIMULATION 8
Guidelines
This is a lab item in which tasks will be performed on virtual devices.
* Refer to the Tasks tab to view the tasks for this lab item.
* Refer to the Topology tab to access the device console(s) and perform the tasks.
* Console access is available for all required devices by clicking the device icon or using the
tab(s) above the console window.
* All necessary preconfigurations have been applied.
* Do not change the enable password or hostname for any device.
* Do not replace existing routing policies or configurations.
* Save your configurations to NVRAM before moving to the next item.
* Click Next at the bottom of the screen to submit this lab and move to the next question.
* When Next is clicked, the lab closes and cannot be reopened.
Topology
Tasks
Troubleshoot R-WEST to achieve the desired results:
1. All the commands should be locally saved to the router as well as sent to the Syslog server
except passwords.
2. All the Cisco OSPF LSA traps should be sent to the SNMP server.
Guidelines
This is a lab item in which tasks will be performed on virtual devices.
* Refer to the Tasks tab to view the tasks for this lab item.
* Refer to the Topology tab to access the device console(s) and perform the tasks.
* Console access is available for all required devices by clicking the device icon or using the
tab(s) above the console window.
* All necessary preconfigurations have been applied.
* Do not change the enable password or hostname for any device.
* Do not replace existing routing policies or configurations.
* Save your configurations to NVRAM before moving to the next item.
* Click Next at the bottom of the screen to submit this lab and move to the next question.
* When Next is clicked, the lab closes and cannot be reopened.
Topology
Tasks
Troubleshoot R-WEST to achieve the desired results:
1. All the commands should be locally saved to the router as well as sent to the Syslog server
except passwords.
2. All the Cisco OSPF LSA traps should be sent to the SNMP server.
Correct Answer:
