IBM AIX Administration V1 (C9010-022) Free Practice Test

Question 1

Which level of information does the mpstat command provide when run inside an LPAR?

A. Number of online physical processors in the pool where the LPAR resides.

B. The simultaneous multi-threading LPAR profile setting.

C. Performance statistics for all logical processors inside the LPAR.

D. Overall managed system logical processors utilization.

Correct Answer: C

Question 2

How can a system administrator verify the progress of an AIX 7.1 client installation from the NIM master?

A. nim -status

B. nim-o check

C. Isnim-I

D. tail-f/var/adrn/ras/nimclient

Correct Answer: C

Question 3

Which standard filesystem is temporarily used by the mksysb backup process?

A. /var/ras/tmp

B. /tmp

C. /usr/tmp

D. /mnt

Correct Answer: A

Question 4

An existing LPAR is configured with a vSCSI disk for a root volume group. An administrator is configuring NPIV to provide secondary storage to the partition. DLPAR operations are used to add the required client and server adapters to the client and VIO Server partitions.
Once the NPIV adapters have been configured, what action should be taken against the client LPAR to ensure access to SAN storage is not compromised?

A. Add the physical WWVPN to the virtual device configuration.

B. Shutdown and reboot AIX.

C. Shutdown and reactivate the profile.

D. Save the current configuration to a profile.

Correct Answer: D

Question 5

How can an administrator enable the Workload Partitions Manager feature after AIX 7 has been installed with the default options?

A. Change AIX edition using chedition -e command

B. Change WPAR edition using chwpar-e command

C. Change WPAR License using chwpar -I command

D. Change AIX License using chlicense -I command

Correct Answer: A

Question 6

Based on the following output, what must be done if loglv1 name is changed to db2loglv?

A. Run the logform command to update the log format of db2loglv.

B. Run the chfs command to update /exportfs/db01 logging logical volume to db2loglv.

C. Run the chvg command to update volume group default logging logical volume to db2loglv.

D. Run the chlv command to update dblv01 logging logical volume to db2loglv.

Correct Answer: D

Question 7

When creating a new user id, an administrator encounters the following error message:
aixsystem:/home/root# mkuser newuserid
3004-694 Error adding "newuserid": Name is too long.
Running which of the following commands will cause the mkuser newuserid command to complete successfully?

A. Option D

B. Option C

C. Option A

D. Option B

Correct Answer: C

Question 8

Which TWO components of IBM Systems Director are included in a new installation of a AIX 7.1? (Select 2)

A. Interface Agent

B. Platform Agent

C. Compliance Agent

D. Distributed Agent

E. Update Agent

F. Management Agent

G. Common Agent

Correct Answer: B,G

Question 9

The AIX hosts node1 and node2 have Ethernet adapters, both named ent0, configured on the same network. Both are dedicated physical 1GB adapter ports in a Host Ethernet
Adapter. Based on this information and the output shown for each node, what is the most likely cause of intermittent failures and slow communication between these adapters?

A. The Multi-Core Scaling mode is enabled. Multi-Core Scaling is interfering with communications because the processor is too busy.

B. The media speed is set differently on the adapters than the endpoints on the switch.

C. The Shared Ethernet Adapter does not have enough bandwidth to accommodate the network traffic.

D. The jumbo_frarnes setting is 'no' and should be set to 'yes'.

Correct Answer: B

Question 10

The/app1 filesystem in appvg did not mount due to a failure replaying jfslog1. Which command will reinitialize jfslog1?

A. logform/dev/jfsiog1

B. synclvodm appvg jfslog1

C. format-d/dev/jfslog1

D. resysnclvodm -vjfslog1

Correct Answer: A

Question 11

What determines whether all AIX systems in the virtual environment are at a specified software and fix level and provide an alerting mechanism?

A. IBM PowerVC - Virtualization Center

B. Security and Compliance Automation

C. Trusted Network Connect and Patch Management

D. AIX Network Install Manager

Correct Answer: D

Question 12

A system administrator wants to create a server with network redundancy and maximum I/O throughput over two Ethernet cards. Which option will support the requirement?

A. Create an 802.3ad Link Aggregation adapter backed by both Ethernet cards and cable to a switch with 802.3ad enabled ports.

B. Create a virtual adapter and assign it to the server, use both Ethernet adapters as backing devices to the virtual adapter with the mkvdev command. Have each adapter cabled to separate switches.

C. Create a Network Interface Backup (NIB) with each Ethernet card being cabled to a different switch.

D. Create the file /etc/sysconfig/network-scripts/ifcfg-bond0 then edit the two ifcfg-ethX configuration files to add a master or slave option. Cable to two switches and use 802.3ad enabled ports.

Correct Answer: A

Welcome to TestSimulate

IBM AIX Administration V1 (C9010-022) Free Practice Test