Fast Track - Applying Aruba Switching Fundamentals for Mobility (HPE2-Z39) Free Practice Test

Question 1

This exhibit shows the topology for a company campus LAN.
Each access layer switch will be the default router for the devices connected to it.
The company needs to permit the following:
* Communications between devices in an subnets
* Support for efficient traffic paths during normal operation and in situations in which a link fails
* Fast failover if a link fails
Which feature should the network administrator configure on the ArubaOS switches to support these requirements?

A. RIP

B. Static Routes

C. MSTP

D. OSPF

Correct Answer: C

Question 2

A network administrator configures LLDP-MAD on an Aruba Virtual Switching Framework
(VSF) fabric. The administrator needs to enter an SNMP
community string after v2c in this command:
Switch:(config) # vat lldp-rnad ipv4 10.1.0.2 v2c ----------------
Which SNMP community string should the administrator enter?

A. one configured on the standby member in the fabric

B. one configured on the device at 10.1.0.2

C. one configured for the VSF fabric on AirWave

D. one configured on the VSF fabric as a whole

Correct Answer: A

Question 3

A network administrator connects several new Aruba Instant APs (at factor/ defaults) to a switch.
After waiting several minutes for the cluster to form, the administrator is ready to provision the cluster.
The VLAN on the ports connected to the APs has no DHCP services.
How can the administrator contact the Instant Ul and provision the APs with static IP addresses?

A. Access the default IP address. 192.168.1.1. from a device connected in the AP VLAN.

B. Connect to the Instant SSID and open a Web browser.

C. Access the cluster using Aruba Activate.

D. Access https://vc.arubanetworks.com from a device connected in the AP VLAN.

Correct Answer: C

Question 4

What is one reason to configure a dynamic LACP link aggregation instead of a static link aggregation?

A. so that the link aggregation automatically chooses its operational key

B. so that the link aggregation can detect the system ID and operational key on the other side of each link

C. so that the link aggregation can include more interfaces with some interfaces on standby

D. so that the link aggregation can automatically change a passive LACP interface to active mode

Correct Answer: B

Question 5

A network administrator has set up a link between two ArubaOS switches. Both switches have an IP address in VLAN 1 and can ping each other in VLAN 1. The administrator then creates VLAN 2 and tags it on the same link of both switches.

A. Use LLDP to test connectivity.

B. How can the administrator verify that the connectivity in VLAN 2 is functional between the two switches7 Use either LLDP or ARP to test connectivity.

C. Assign each switch an IP address in VLAN 2. and use ICMP to test connectivity.

D. Assign each switch an IP address in VLAN 2. and use LLDP to test connectivity.

Correct Answer: A

Question 6

Exhibit 2 shows the IP routine tables for all the switches after the link between Switch-4 and Switch-2 failed '//'hen.
This link fails traffic between 10 1 3 0/24 and 10.1.2.0724 is disrupted.
What should the network administrator do to ensure that this traffic continues to flow if this link fails in the future? (Assume that routes on Switch-1 and Switch-3 are correct.)

A. Add a route to 10.1.2.0/24 through 10.1.0.14 on Switch-2.

B. Add a route to 10.1.3.0/24 through 10.1.3 1 on Switch-4.

C. Add a route to 10.1.3.0/24 through 10.1.0.14 on Switch-2

D. Add a route to 10.1.2 0/24 through 10.1.2.1 on Switch-4.

Correct Answer: A

Question 7

Two ArubaOS switches connect on a VLAN. and both enable OSPF on that VLAN. Which
VLAN OSPF setting must match for the switches to become fully adjacent neighbors?

A. area ID

B. router ID

C. DR priority

D. cost

Correct Answer: B

Welcome to TestSimulate

HP Fast Track - Applying Aruba Switching Fundamentals for Mobility (HPE2-Z39) Free Practice Test