Avaya Ethernet Routing Switch Implementation Exam (6101.1) Free Practice Test

Question 1

A customer needs to install a new Ethernet Routing Switch (ERS) 2550T on the 172.16.5.0/24 network, but does not have a console cable available.
Which statement is correct?

A. The switch will first attempt to use BootP to acquire an IP address, and if that fails it will assign IP address 192.160.1.1/24 to the switch IP.

B. The customer can set the switch to use the temporary address of 192.168.192.168 by pressing the User Interface button on the front of the ERS 2550T

C. The customer can connect to the network management Ethernet port which is pre-configured to use the 192 168 1 1/24 IP address

D. To communicate with an ERS 2550T the IP address must first be set though the console interface.

Correct Answer: C

Question 2

Consider the fallowing port conditions on an Ethernet Routing Switch (ERS) 8648GTRS 10/100/1000 Ethernet I/O module left LED -green Right LED - flashing green
What is the status of the port?

A. The link speed is 100 Mbps. and the port is disabled.

B. The link speed is 100 Mbps. and the port is passing traffic.

C. The link speed is 1000 Mbps, and the port is disabled

D. The link speed is 1000 Mbps. and the port is passing traffic.

Correct Answer: B

Question 3

After issuing a show mlt list stats (CLI) or show ist Stat (ACLI) command, it is determined that the running type is normal MLT and not 1ST
What are two causes of the IST not running properly? (Choose two)

A. The MLT ID does not match on both switches.

B. The peer IP addresses have to be 192.168.1.1/30 and 192.168.1.2/30.

C. The peer IP address is not the address of the peer switch IST VLAN.

D. The IST is not enabled on both switches.

Correct Answer: A,C

Question 4

An engineer needs to assign an IP address of 172 25 10.31 for out of band management of an Ethernet Routing switch (ERS) 8600 switch a subnet mask of 255.255.255.192.
Which command line interface (CLI) command should the engineer use?

A. ERS8600:5# config bootconfig set ip 172.26.10 36/26

B. ERS8600:5# config bootconfig net mgmt ip 172.25.10.36/27

C. ERS8600:5# config bootconfig net mgmt ip 172.25.10.36/26

D. ERS8800:5 # config bootconfig set ip 172.25.10 36/27

Correct Answer: C

Question 5

What is the front panel port configuration for the Ethernet Routing Switch (ERS) 2550TPWR?

A. 50 10/100BaseT ports (PoE on 25 ports) two combo 10/100/1000BaseT or SFP port

B. 48 10/100 BaseT ports (PoE on 48 ports) Two combo 10/100/1000BaseT or SFP port

C. 48 10/100BaseT ports (PoE on 24 ports) two combo 10/100/1000BaseT or SFP port

D. 50 10/100BaseT ports (PoE on 50 ports) two combo 10/100/1000BaseT or SFP port

Correct Answer: C

Question 6

The Ethernet routing switch (ERS) 5000 switches are being upgraded and it appears that a license is not recognized on the switch.
Which two statements are valid sources of information that will help resolve the license installation? (Choose two.)

A. Check the record of MSG address changes

B. Use the show license command to get the license installation status

C. Check for an 'invalid license fife' log report

D. Use the show license file command to get the license installation status.

E. Check to see if the MAC address is correct in the license file.

Correct Answer: B,E

Question 7

Set of procedures will upgrade the boot monitor on an Ethernet Routing switch (ERS) 8600 with a single 8692SF module?

A. Copy the new Image to flash Boot the new image

B. Boot the new image

C. Modify the boot choice for run-time image

D. Copy the new image to flash Activate new image with SF module in service

E. Copy the new image to flash Modify the boot choice for rim-time image Boot the new image

Correct Answer: B

Welcome to TestSimulate

Avaya Ethernet Routing Switch Implementation (6101.1) Free Practice Test