Avaya Ethernet Routing Switch Implementation and Maintenance Exam (3605) Free Practice Test

Question 1

Simple Loop Prevention Protocol (SLPP) detects VLAN based network loops.
Which two statements about SLPP functionality are correct? (Choose two.)

Correct Answer:

Explanation: Only visible for TestSimulate members. You can sign-up / login (it's free).

Question 2

What is the maximum number of Gigabit Ethernet ports on a single Ethernet Routing Switch (ERS) 8300 Input/Output module?

A. 50

B. 48

C. 16

D. 24

Correct Answer: B

Question 3

A technician wants to control the routes being added to the routing table from the BGP routing table. Which statement describes how to do this?

A. BGP adds all new priority routes to the routing table.

B. Metrics determine which routes are inserted into the routing table,

C. BGP filters are applied only to external route information.

D. BGP filters are applied to all incoming route information.

Correct Answer: B

Question 4

A technician has installed a license file on the Ethernet routing switch (ERS) 8800 and rebooted, but cannot configure the associated licensed features. it has been determined that license did not load properly at booyup time. Which two must be verified?

A. The license file has .dat extension.

B. The switch is at the current release.

C. The license file is stored in the flash directory

D. The appropriate license level has been obtained.

E. The license filename contains valid characters.

Correct Answer: A,E

Question 5

The User interface (Ul) button on the Ethernet Routing Switch (ERS) 6500 can be used to temporarily reset a switch to the default IP address. Which two statements are true about the default IP address set via the Ul button? (Choose two)

A. the default IP address is saved in NVRAM across resets of the switch/stack.

B. The default IP address overwrites the "configured" IP address settings that are set via console. CLI or Web.

C. the default IP address changes if there is a change in the state of the switch, such as if the switch joins or leaves a stack.

D. The default IP address overrides the IP address currently in use by the switch stack.

Correct Answer: B,D

Question 6

An Ethernet Routing Switch (ERS) 8600 is being configured for Virtual Router Redundancy Protocol (VRRP). If the default value is used on the peer switch, which CLI command would cause this switch to e the VRRP master?

A. Config vlan 100 ip vrrp 100 priority master

B. Config vlan 100 ip vrrp 100 master

C. Config vlan 100 ip vrrp 100 priority 250

D. Config vlan 100 ip vrrp 100 priority 1

Correct Answer: C

Question 7

A technician is configuring 802.1Q tagging, Virtual Link Aggregation Control
Protocol (VLACP) with short timeout, and untagged frames to be discarded.
Which part of the network is being configured?

A. IST

B. The uplinks

C. The edge access ports

D. The out-of-band management port

Correct Answer: B

Question 8

Consider the fallowing port conditions on an Ethernet Routing Switch (ERS)
8648GTRS 10/100/1000 Ethernet I/O module left
LED -green Right LED -
flashing green. What is the status of the port?

A. The link speed is 100 Mbps. and the port is disabled.

B. The link speed is 100 Mbps. and the port is passing traffic.

C. The link speed is 1000 Mbps, and the port is disabled

D. The link speed is 1000 Mbps. and the port is passing traffic.

Correct Answer: B

Question 9

Refer to the exhibit.
A campus network has been established with four Ethernet Routing Switch (ERS) 8600 switches in a switch cluster, two pairs with an Inter Switch Trunks (IST) running Split Multi Link Trunk (SMLT) and Routed Split Multi-Link Trunking (RSMLT). The traffic filters are required to block specific source IP addresses to be forwarded through the core. With reference to the exhibit, how should these filters be set up?

A. Apply the filters to all ports that receive traffic from outside the immediate switch cluster.

B. Configure and apply all the filters on the two core IST links only

C. Configure the filters on the 1ST first before any other ports.

D. Configure the filters on the ports first and then the IST.

Correct Answer: A

Question 10

What is Enterprise Policy Manager (EPM) used for in an Enterprise network?

A. as an alternative to EA servers

B. to assign user role attributes on the RADIUS server

C. to distribute control of packet classification for resiliency and efficiency

D. to manage
traffic
prioritization
and network
access
security for
business applications

Correct Answer: D

Question 11

What does Ping snoop identify?

A. Which port filter is best to use on MLT networks

B. Rate limiting for ICMP traffic

C. The rate of IP traffic flow

D. The path that IP traffic takes over an MLT or SMLT

Correct Answer: D

Question 12

Confirm that RSMLT will work on a set of VLANs.
Which
network design aspect should
be considered?

A. RSMLT is enabled on each SMLT VLAN on which the function is required

B. RSMLT is enabled on all SMLT VLANs.

C. RSMLT is enabled on the VLAN group.

D. Router 1 always owns the network.

Correct Answer: A

Question 13

Consider four software upgrade events on an Ethernet Routing Switch (ERS)
2500 series switch:
1.Upgrade the software image
2.The System Reboots
3.Backup the binary configuration to a TFTP server
4.Upgrade the boot/diagnostic code, if the new version is available Which sequence of events will correctly upgrade the software?

A. 3.2.1.4

B. 1.4.2.3

C. 3.2.4. 1

D. 3.4.2.1

E. 1.2.4.3

Correct Answer: D

Question 14

A technician has complied me configuration of an Ethernet Routing (ERS) 5520 to and now must transfer a backup copy of configuration file to server. Which command is used to accomplish this task?

A. 5520-24T-PWR# copy config ftp filename ers5520config.cfg

B. 5570-74T PWR# copy config tftp filename ers5520COnfig.cfg

C. 5520-24T-PWR# copy config scp filename ersS520conftg.cfg

D. 5520.24T-PWR> copy config ftp filename ers5520 config.cfg

Correct Answer: B

Welcome to TestSimulate

Avaya Ethernet Routing Switch Implementation and Maintenance (3605) Free Practice Test