HP Deploying HP Enterprise Networks Sample Questions:

1. Click the Exhibit button.

A provider of MPLS services configures MPLS Layer-3 VPN services for two customers. Each customer has three branch offices that will be interconnected by MPLS Layer-3 VPNs. The Route-Distinguisher and VPN-Target used for each customer is shown in the following chart: All Customer A sites can ping each other; all Customer B sites can ping each other. Customer A Site 1 needs access to Customer B Site 3. Other Customer A sites should not be able to access any Customer B site. Without changing the configuration of PE-2, which configuration changes should be made to achieve this goal?

A) Import vpn-target 100:92 for Customer A Site 1 and export vpn-target 100:91 for Customer B Site 3.
B) Import and export route-distinguisher 100:163 for Customer A Site 1 and Customer B Site 3.
C) Import route-distinguisher 100:82 for Customer A Site 1 and export route-distinguisher
100:81
for Customer B Site 3.
D) Import vpn-target 100:500 for Customer A Site 1 and export vpn-target 100:600 for Customer B Site 3.
E) Import and export vpn-target 100:163 for Customer A Site 1 and Customer B Site 3.

2. A provider of MPLS services in Autonomous System 100 offers multiple types of MPLS-based VPNs to its customers. Which types of MPLS VPNs are broken if the following command is executed on all Provider Edge LSRs? (Select two.)undo bgp 100

A) MPLS L2VPNs Martini version
B) MPLS L3VPNs
C) VPLS Kompella version
D) VPLS Martini version

3. Click the Exhibit button.

In this star topology, router HKG is the hub. Routers SIN, SGN, and KUL are spokes and are not interconnected. A review of the network reveals that SGN is able to reach the RP at HKG, loopback 0 10.1.254.1. Receiver 10.4.1.231, which is an IGMPv2 device, cannot receive the multicast stream 232.0.0.1 from 10.1.1.1. Which command will enable
10.4.1.231 to receive the multicast stream 232.0.0.1?

A) [HKG-VLAN-interface100] igmp ssm-mapping enable
B) [SGN-VLAN-interface400] igmp ssm-mapping enable
C) [SGN] igmp ssm-mapping enable
D) [SGN-VLAN-interface100] igmp ssm-mapping enable

4. You are importing RIP routes into OSPF and have been asked to filter out selected routes. In particular, you want to import only 192.168.x.x routes that have a /24 mask.

You decide to use a prefix-list to filter the routes and then reference them in a route-policy. How should you configure the prefix-list using a single statement on an HP A-Series switch?

A) ip ip-prefix prefix1 deny 192.169.0.0 16 greater-equal 24 less-equal 24
B) ip ip-prefix prefix1 permit 192.168.0.0 16 greater-equal 24 less-equal 24
C) ip ip-prefix prefix1 deny 192.168.0.0 16 greater-equal 24 less-equal 24
D) ip ip-prefix prefix1 permit 192.168.0.0 8 greater-equal 24

5. Click the Exhibit button.

The IRF link has failed between Slave 2 and Slave 3 in an IRF stack. MAD BFD was enabled and functional before the failure. Which action should you take to correct the failure?

A) Reconnect the IRF link and reboot the Master.
B) Reconnect the IRF link and reboot all the devices.
C) Reconnect the IRF link and reboot Slave 2 and Slave 3.
D) Reconnect the IRF link and reboot Slave 3 and Slave 4.

Solutions: